BAKER
PUMP JACKS

DEAN BENNETT SUPPLY
Toll Free   800 - 621 - 4291
BAKER  ZA  HEAVY DUTY PUMP JACKS

Baker Pump Jack Repair Parts

 
                  N/A #18-ZA     BAKER  ZA  pump jack for use with up to 2 hp electric motor
                  N/A #20-ZA     BAKER  ZA  pump jack for use with a gasoline engine
          $   159.00 #90-ZA     Replacement pair of 48" long pumping angles
THE BAKER / MONITOR PUMP JACKS are low cost, high quality units used to reciprocate a pump cylinder. They consist of a helical gear speed reducer driving two pumping arms ( cranks ) which are connected to the sucker rod by two long pumping angles and a cross head. These jacks are V-belt driven by either an electric motor or a gasoline engine mounted directly on the jack. Compared to worm gear pump jacks, Baker's jacks deliver 50% more power to the sucker rod. All these models are shipable via UPS.
THE BAKER   ZA   pump jack is a heavier duty model designed for deeper wells, heavier loads, and up to 2 hp motor. The pump jack can be mounted on a hand pump or directly on the well pipe itself. A spring-held pump rod pin in the crosshead can be quickly attached or withdrawn. The motor mount is easily adjusted for the base of your electric motor or gas engine and your V-belt length. You can operate the ZA pump jack during a power failure by rotating the jack's pulley with auxiliary power.
SPECIFICATIONS:   Maximum pump rod load is 1,500 lbs   ZA jack is geared 9 to 1   Stroke is 6" Maximum of 42 strokes per minute   Weight is 131 lbs		 Baker pump jacks allow you to stroke a well pump cylinder with a gas or electric motor.

DEMPSTER WORM GEAR PUMP JACKS


$ 1285.00
COMPLETE DEMPSTER PUMP JACK

$ 1039.00

 DEMPSTER PUMP JACK GEARCASE

$     85.00

 PAIR of 48" LONG PITMAN ARMS

COMPLETE JACK:   The model BB33-H ( for use with an electric motor ) includes the basic pump jack gearcase, 2 - 48" long pitman arms, crossbar assembly, motor mounting base with motor rails, 8" diameter V-pulley w/ 7/8" bore for jack, 2-1/2" diameter V-pulley w/ 5/8" bore for motor, and 34" long V-belt. Electric Motor IS NOT included in price. Electric motor MUST run counter-clockwise as you face the pulley end of motor.
GEAR RATIO & STROKE:   Gear ratio is 16 to 1 with a stroke length of 6"   recommended maximum is 40 strokes per minute ( 640 RPM shaft speed )
HELICAL MACHINE-CUT GEARS:   Precision worms and gears follow a spiral design for a smooth drive. Worms and gears operate right and left, balancing the load and reducing wear, and are pinned to the shaft to maintain proper timing.
GEARS RUN IN OIL:   Oil seals on all shafts retain lubricant and shut out dirt and moisture from individual gear enclosures on each end.
CROSSHEAD COUPLING: Fits 7/16" x 1" flatbar, which must have 12" or more above crosshead for clear operation. Jack gearcase can be attached to slightly larger or smaller barrel by carefully shimming and positioning the U-bolt.
LOAD LIMITS:   The Dempster Pump Jack should not be used with greater than a 1/2 hp electric motor or a 1-1/2 hp gasoline engine. The speed must not exceed 40 strokes per minute ( 640 RPM shaft speed ) under any circumstances.


Dempster worm gear pump jacks are used to pump water from shallower depths.


The complete Dempster worm gear pump jack ready to install on a hand pump to hold it in place.

PUMP JACK CAPACITY TABLE

DEMPSTER PUMP JACKS

BAKER PUMP JACKS
HEAD IN FEET CYLINDER GALLONS HEAD IN FEET
1/3 hp 1/2 hp DIAMETER PER HOUR 3/4 hp 1 hp 1-1/2 hp 2 hp
140 205 1-7/8" 172 154 205 308 410
125 180 2" 195 140 187 281 374
100 145 2-1/4" 247 117 157 235 313
75 100 2-1/2" 306 99 133 199 265
60 90 2-3/4" 370 85 114 170 227
50 80 3" 440 73 98 147 196

FREIGHT IS PREPAID IF ORDER IS OVER  $  1,000.00


Above prices effective August 10, 2008

HOME        Contact us

Download our catalog in pdf format