WINDMILL
CYLINDERS

DEAN BENNETT SUPPLY
Toll Free   800 - 621 - 4291

# 449-B    ALL BRASS   OPEN TOP   WINDMILL CYLINDERS

          $ 195.00 1-7/8" x 14" Stroke x 24" Overall Length    
for 2" Pipe   &  5/8" Rod		 Open top working barrel cylinder allows you to change cup leathers without pulling the whole string of pipe from the well.
          $ 207.00 1-7/8" x 20" Stroke x 30" Overall Length    
for 2" Pipe   &  5/8" Rod
          $ 278.00 2-1/4" x 19" Stroke x 30" Overall Length    
for 2-1/2"     &  7/8" Rod
          $ 425.00 2-3/4" x 18" Stroke x 30" Overall Length     
for 3"Pipe    &  7/8" Rod
The #449-B  all brass open top style cylinder allows for both the plunger assembly and the bottom check to be pulled for service without pulling the steel drop pipe. All are constructed of 13 gauge seamless brass tubing, with all brass caps, a 3 leather ball valve brass plunger, and a ball valve brass bottom check.

# 442    ALL BRASS   FLUSH CAP   WINDMILL CYLINDERS

   Flush cap cylinders are used in shallower wells where you will pull the pipe to change leathers.
$ 143.00 2" x 10" Stroke x 18" Overall Length
for 1-1/4" Pipe   &   7/16" Rod
$ 163.00 2-1/4" x 10" Stroke x 18" Overall Length
for 1-1/4" Pipe   &   7/16" Rod
$ 182.00 2-1/2" x 10" Stroke x 18" Overall Length
for 1-1/4" Pipe   &   7/16" Rod
$ 249.00 3" x 10" Stroke x 18" Overall Length
for 1-1/4" Pipe   &   7/16" Rod
$ 265.00 3" x 12" Stroke x 20" Overall Length
for 2" Pipe   &   7/16" Rod
$ 437.00 4" x 13" Stroke x 20" Overall Length
for 2" Pipe   &   5/8" Rod
The #442 cylinder is all brass and is made from seamless brass tubing. Its flush cap design
(no outside caps) allows you to install a larger cylinder in a smaller diameter well.

#442 ALL-BRASS SLIM-LINE CYLINDERS TO ENTER 2" SCH 40 PIPE

The two sizes of #442 All-Brass "Slim-Line" Cylinders are designed for entry into 2" wells. Many driven wells have less than straight shafts, and therefore may possibly hinder placement of a well pumping cylinder for your windmill or hand pump. Also Old Pipe tends to corrode over time and can cause problems putting a cylinder pump down the well. We offer both sizes that will go into 2" Sch 40 pipe, however we recommend that if your shaft is crooked or has a lot of corrosion, that you choose the 1 11/16" cylinder, since the extra 1/8" may be the difference between a successful installation or a hang up.

$ 155.00 1 11/16" x  10" x  18"    #442 All Brass Cylinder tapped for 1" pipe and 7/16" rod, with a 10" stroke area.
$ 135.00
1 13/16" x  10" x  18"    #442 All Brass Cylinder tapped for 1" pipe and 7/16" rod, with a 10" stroke area.

A-40    CAST IRON   BRASS LINED   WINDMILL CYLINDERS

$ 229.00

 2" x 10" Stroke x 16" Overall Length
for 1-1/4" Pipe   &   7/16" Rod		 Cast iron, Brass lines well pumping cylinders are tough as nails.

$ 265.00

 2-1/4" x 10" Stroke x 16" Overall Length
for 1-1/4" Pipe   &   7/16" Rod

$ 260.00

2-1/2" x 10" Stroke x 16" Overall Length
for 1-1/4" Pipe   &   7/16" Rod

$ 299.00

 3" x 10" Stroke x 16" Overall Length
for 1-1/4" Pipe   &   7/16" Rod
These cylinders have a heavy cast iron body, a brass inside liner, a 2 leather all brass plunger, all brass bottom check poppet, 7/16" galvanized plunger rod, and heavy outside cast iron caps that are tapped for 1-1/4" pipe.


DEEP WELL WINDMILL CYLINDERS

CYLINDER REPAIRS     HOME     HAND PUMPS      PUMP JACKS


SUBMERSIBLE PUMP BELOW A WINDMILL CYLINDER

Price effective 2/1/2007

Download our catalog in pdf format